Most people start remodel planning with cabinets, countertops, flooring, and paint. The electrical work behind the walls gets less attention, but it shapes almost everything else: where the appliances can go, how the room is lit, and whether your panel can handle what you're adding.
Planning the electrical work early, before the walls are closed and the cabinets are ordered, is the easiest way to avoid change orders, failed inspections, and outlets in the wrong places. Here's what homeowners in Indianapolis and the surrounding area should plan and budget for when remodeling a kitchen or finishing a basement.
Why Electrical Planning Matters Early
A remodel is the best chance you'll have to update wiring cheaply and cleanly. When the walls and ceilings are open, running a new circuit or moving a switch is far simpler than doing it later through finished drywall.
Bringing an electrician in at the design stage helps you:
Confirm your panel has the capacity and open spaces for new circuits
Place outlets, switches, and lights where you'll actually use them
Catch older wiring that should be replaced while it's exposed
Get the work permitted and inspected the right way
Avoid costly surprises once the project is underway
Kitchen Remodel Electrical Work
Kitchens have more electrical requirements than almost any other room in the house. Even a "cosmetic" kitchen update can trigger electrical work once you change the layout or add appliances.
Dedicated appliance circuits
Many kitchen appliances need their own circuit. Depending on your appliances and local code, that commonly includes:
Electric range or cooktop and wall ovens
Dishwasher
Garbage disposal
Built-in or over-the-range microwave
Refrigerator (often recommended even where not required)
If you're switching from gas to an electric or induction range, plan for a new high-amperage circuit, and confirm your panel can support it.
Countertop outlets and small-appliance circuits
Kitchen countertops need enough outlets that you're never stretching a cord across the counter, and those outlets are on dedicated small-appliance circuits. Kitchen islands and peninsulas have their own requirements too. Countertop outlets also need GFCI protection. If your current kitchen has just one or two outlets along the backsplash, expect a remodel to add several.
Lighting
A good kitchen usually has layers of light:
Recessed or ceiling lights for general lighting
Under-cabinet lighting for work surfaces
Pendants over an island or sink
Dimmers so you can adjust the mood
Each layer needs wiring and switch locations planned before the drywall and cabinets go in. Under-cabinet lighting in particular is much easier to wire during a remodel than after.
Extras worth considering
While the walls are open, it's worth asking about:
USB or USB-C outlets at a charging spot
Outlets inside a pantry or appliance garage
Smart switches or dimmers
A dedicated circuit for a beverage fridge or wine cooler
Basement Finishing Electrical Work
Finishing a basement is one of the most popular ways for Central Indiana homeowners to add living space. It's also a project where electrical work can be underestimated, because an unfinished basement often has just a few bare bulbs and a couple of outlets.
New circuits for new living space
A finished basement is really several new rooms. Depending on your plan, you may need circuits for:
A family room or media room (TV, speakers, gaming equipment)
A bedroom or home office
A bathroom, including a bathroom exhaust fan
A wet bar or kitchenette
A home gym or workshop with heavier equipment
Outlets and safety protection
New living areas need outlets spaced throughout the walls so you're not relying on extension cords. Many new circuits in living areas require AFCI protection, which helps guard against arcing faults that can start fires, and areas like bathrooms, wet bars, and unfinished storage spaces typically need GFCI protection. Your electrician will know what applies to your layout.
Lighting a space without much daylight
Basements depend on artificial light. Recessed lighting is a common choice because it keeps ceilings clean, especially where ceiling height is limited. Plan switch locations at every entry point, including the stairs. Good stair lighting with switches at the top and bottom is a safety feature, not just a convenience.
Planning around the panel and mechanicals
In many homes the electrical panel sits in the basement. Your finished layout must keep clear, code-required working space in front of the panel. It can't be boxed into a closet behind shelves or built in tight. Planning this up front avoids having to rework a wall later.
Can Your Panel Handle the Remodel?
This is the question that surprises homeowners most. New kitchen appliances, a basement full of circuits, or an induction range can push an older panel past its limits, especially in homes with 100-amp service or a panel that's already full.
An electrician can do a load calculation to see whether your current service can support the remodel. If it can't, you may need a panel upgrade, and it's much better to know that before the project starts. If you're also thinking about an EV charger in the next few years, mention it now so the panel plan accounts for it. Our guide to the signs your panel needs repair or replacement can help you spot warning signs early.
Older Wiring You May Uncover
Remodels in older homes, including many in Indianapolis, Franklin, and Martinsville, often uncover wiring that should be updated while the walls are open:
Ungrounded two-prong circuits
Cloth-insulated or deteriorating wiring
Undersized wiring or circuits that have been overloaded for years
Previous DIY work that isn't up to code
Building some room into your budget for these surprises is smart. Our post on the importance of home rewiring explains when updating older wiring makes sense.
Permits and Inspections
Most remodels that add or change circuits require an electrical permit and inspection through your city or county. A licensed electrician typically handles the permit and schedules the inspection. Permitted work protects you when you sell the home and gives you confidence the work was done safely. It's one of the many reasons remodel electrical work isn't a DIY job. We cover more in the dangers of DIY electrical repairs.
Electrical Line Items to Plan For
Every remodel is different, so we don't publish one-size-fits-all prices. When you get quotes, these are the electrical items that typically drive the scope:
Number of new circuits, especially high-amperage appliance circuits
Number of outlets, switches, and fixtures being added or moved
Lighting choices, such as recessed cans, under-cabinet lighting, or pendants
GFCI and AFCI protection required for the new work
Panel capacity, and whether a panel or service upgrade is needed
Condition of existing wiring once the walls are opened
Permits and inspections
Access, such as open walls versus finished drywall and basement ceiling height
The best way to get an accurate number is to have an electrician walk the space with your remodel plans in hand.
Tips for a Smoother Remodel
Bring in the electrician before cabinets are ordered. Appliance and outlet locations depend on it.
Walk the room and think about how you'll use it. Where will you charge phones, plug in the coffee maker, or put the TV?
Decide on lighting early. Fixtures and switch locations are hard to change after drywall.
Coordinate with your contractor. Electrical rough-in has to happen at the right point in the schedule, before insulation and drywall.
Ask about future needs. An EV charger, a hot tub, or a home office later may affect today's panel plan.
Frequently Asked Questions
Do I need an electrician for a kitchen remodel?
If you're adding or moving outlets, lights, or appliances, yes. Kitchens have specific requirements for dedicated circuits, countertop outlets, and GFCI protection, and the work generally needs a permit and inspection.
When should the electrician get involved in a remodel?
As early as possible, ideally during design and before cabinets are ordered. Rough-in wiring happens after framing and before insulation and drywall, so the electrical plan needs to be set by then.
Will my remodel require a panel upgrade?
Not always. It depends on your current service size, how full the panel is, and what you're adding. An electrician can run a load calculation and tell you whether your existing panel is enough.
Does finishing a basement require an electrical permit?
In most cases, yes. Adding circuits, outlets, and lighting to create new living space generally requires a permit and inspection. Your electrician can handle that process.
Can I do some of the electrical work myself to save money?
We don't recommend it. Mistakes behind the walls can create shock and fire hazards, fail inspection, and cause problems when you sell. You can save money by planning carefully and making decisions early, so the electrical work is done once.
Remodel Electrical Work in Central Indiana
Whether you're redoing a kitchen in Greenwood, finishing a basement in Plainfield, or updating an older home in Indianapolis, Central Electric can help you plan and complete the electrical side of your remodel. We work with homeowners across Indianapolis, Greenwood, Franklin, Plainfield, Avon, Brownsburg, Mooresville, Martinsville, Bargersville, and Whiteland.
Call 317-644-1322 or request service online to talk about your project. You can also see our full list of residential electrical services.